Jump to content
Forums Gone... but not forgotten!
Pontiac of the Month

Shakercars's 1972 Trans Am

2019 August
of the Month

  • Welcome!

    Welcome to Forever Pontiac, full of great ideas for Pontiac performance, maintenance, or for peer-to-peer assistance from Professional and DIY mechanics. Also, compete in our Pontiac monthly competitions. Please register if you'd like to take part.

Last Indian

Exterior panel stabilization

Recommended Posts

Exterior panel stabilization, securing & attachment improvements that will help quiet them. If you own a Pontiac from the early 1990s through 2009, then you may have noticed that because of how a lot of the panels were made and attached, there can be that creak or crack when you push on a panel like a front bumper cover or rear cover, etc., but these improvements will also help to improve driving characteristics; yes really! The old cars were not and are not like that! Why? Because they bolted together solid, panel to panel, not with plastic push pins that go in a hole almost half again as big as the pin O.D… Well you can have that same solid non noisy panel setup as the old Skool classics have and had. Why would this improve driving characteristics? Well when panels aren’t stable they negatively impact air movement aka air foil characteristics. This may seem irrelevant at 35mph, but not at 50mph! There is a reason NASCAR as well as well as some of the car industry spends millions of dollars on aerodynamic research, wind tunnels and the like!

 

Still for me, when you build a car, you build a car! You build as a a complete assembly, too be as perfect as you can make it, for every instance and every situation! I may be anal, ok I am, but if I was paying to have a car built, this is what I would want, so why should I not do it for myself?! Really! A very simple example is the vertical edge in the engine compartment where the outer and inner fender are spot welded together (see pic)! While there is no value other than aesthetics in this case this is just a case of a little effort to make an improvement and remove an edge that can get beat up easily and inflict some damage to knuckles or the like.

 

So to the details, again I will use my 2000 Grand Prix for example purposes. First the front end. I’ll start with the bumper support, this piece attaches to the lower hood latch and supports the upper area of the bumper cover with two push pins and one small screw/washer, but also attaches to the steel brace/bracket that the headlights attach. This where I make an adjustment to effect the height of the bumper cover height gap to the hood. I do this by retapping the hole from 6mm x 1.25mm to ¼ x 20 thd… and then placing stainless steel washers between the bumper support and the steel headlight bracket with a SS ¼-20 buttonhead screw through the middle of the washers. This piece also has the ability to be adjusted to some degree at the bumper cover attachment area itself. This includes the fact that it interfaces with the two air ducts for radiator cooling that locate it vertically on molded post of those ducts. These could be shortened or raised by the addition of a spacer if need be. This will in turn changes the gap between the upper lip of the cover and the hood. Likewise the two headlight brackets need to be fixed, as they are not attach properly as a support structure. They allow for to much movement and vibration as they come from the OEM. There are two places I will show to attach these brackets to the core support to make them solid like they should be. This structure with its long span between the factory attachment points at each end of the bracket needs to be made ridged. The two outer holes of the bumper support that interface with the bumper cover will not use the push pin fasteners. Instead it will change to SS ¼-20 buttonhead screws with a SS washer and nut on the underside. This now holds the upper bumper cover tight to the support so there is no movement or flex. 
 

 

9668181A-FC1B-4E29-9278-C15EB13312F5.jpeg

019DBC36-92DB-49E9-B57D-F5788FD348FE.jpeg
the two pictures above show the vertical edge fix.

C1795DBE-DBDF-47F4-A5F6-9CEE82395BAC.jpeg

28D1184F-7695-420D-9EDB-7966318B7FF3.jpeg

0F47E5DF-EE76-4B50-A7F8-9E9EE5BDB835.jpeg

5AE75191-A18F-4413-A0D2-90AB5F90DE61.jpeg

ADB86D8D-3CD7-4667-86B4-AC69E040F6EE.jpeg

2D7AEF29-C21E-41B6-A2E4-E3B57D0AB7EC.jpeg
this top portion area fix is the easy part! The bottom side gets much more involved, that will be the next segment.

Edited by Last Indian
  • Like 1

Share this post


Link to post
Share on other sites

Tired of these Ads? Register Today!

Great info as always, thankz for sharing......And Happy Birthday.

Share this post


Link to post
Share on other sites
1 hour ago, JUSTA6 said:

Great info as always, thankz for sharing......And Happy Birthday.

Thanks buddy! One step closer to that 70 1/2 mark so Uncle Sam can start getting his tax money back 😬

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Tired of these Ads? Purchase Enhanced Membership today to remove them!
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.