Jump to content
Forums Gone... but not forgotten!
Pontiac of the Month

FBIRD69's 1969 Firebird

2024 March
of the Month

Ponchoguy

Members
  • Posts

    21
  • Joined

  • Last visited

Everything posted by Ponchoguy

  1. RamAir Restorations Manifolds. 3” long tubes, three inch pipes to Spintech mufflers. 24” long pipes 3” obviously. Then turn downs. Motor is a 400 bored and stroked to 468 IMG_1081.MOV
  2. I mentioned I could read between lines and that makes me feel like I was getting what you were putting down!! AWESOME!!
  3. That I can appreciate.. that’s something substantial. THANK YOU!! I can read between the lines.. I really appreciate that. That being said.. I could not find a real good oil for a Honda I had, it had a wet clutch and people got funny about that.. I finally found someone that swore by rotella T5 and I had great success with that. 15-40 isn’t far off from 2O-50 I’ve also seen 10-30 Rotella!! 🙏🙏🙏🙏
  4. I have been having a lot of problems keeping my transmission holding together. I’ve built a 700r4 and smoked it the first week. Took it out and sent it back in and the upgraded the internals and I put it back in. Took it out this afternoon and I made sure 100% the tv cable has PLENTY of pull. I have an extra spring on the end of the cable and it still shifts “greasy” NOT firm. I’ll pull it AGAIN and make sure the pump is not leaking somewhere... but I now have the opportunity/option to buy a NV833 or A833 4 speed. Has anyone done this swap. I’m probably going to make this change.. any desire for me to document this change?? I’d love the feed back if you have any!! Thank you 🙏
  5. Thank you for the great info, can I ask a question? Not trying to be smart at all.. but.. I just read through almost all of this thread.. what exactly does an oil expert recommend for a street car? Again I feel you are probably the one we should be listening too.. right??? I don’t mean viscosity that should be more left to the climate of the owner, I get that much. I’d like to hear you say a recommendation on brand and type? You have convinced me sir. I read a little nod to Castrol but can I make you give a real honest “I recommend “ this : Again your insight has been really good reading, thank you 🙏
  6. I. NEVER wanted anyone to kick sand. This was supposed to be an informative thing from the start. 🤷🏼‍♂️
  7. I’ve been a Master Diesel mechanic for year and tears... thing thing about oil samples is you’re good, you’re good, you’re good, you’re fucked. Now that being said.. if you are hauling a perishable product and a breakdown is an CATASTROPHIC event.. then oil analysis is definitely worth the money.. if not I would recommend cutting your oil filter at changing and look for glitter.. WAY cheaper!! Jmho!!!
  8. Absolutely, I never tried to make an argument... I’m sorry if I came off like and a$$ we are absolutely 100% good. Like I said.. I Really appreciate the great info🙏🙏🙏 Car guys gotta stick together!!!
  9. Sure, I can do that Kiwi! TBN stands for total base number. This comes minimally from the base stock of oil but mostly from the additive package. This numbe This is kinda what I was looking for when I started this post... what do You run.. and why.. maybe Dad did.. maybe you had a bad experience with X brand.. this was supposed to be just a round table chat... THATS ALL!!!
  10. Disqualified.. Chevy!?!?! Just messing.. great Not a common Pontiac!! Thumbs up.. but seriously find a 400 Pontiac you won’t be disappointed!!😇
  11. I’ll look tomorrow at work from my desk top not my stupid phone .. especially after looking at my spell check and Grammer from the other night. I will however state that from the beginning of this post.. I said roll call.. which means hey everyone.. what oil do you use and why??????? It was a conversation topic to start.. I’m not looking back at my exact words tonight.. but it was basically here it what was recommended to me.. NOT this is my oil!!! That’s why I even started this post.. I’ve never even heard of Brad Penn until I had my 468 built by probably the best engine builders in West Michigan. I was just looking for AND I LITERALLY QUOTE!!!!!!!! “ What do you run and why” so seriously before you start the next rant.. read what I write... COOL!??!?’
  12. Man.. I bet you are the LIFE at parties!! JK .. great info!! I’ve seen my machine shop build engines that spend their time above 10,000 rpm think about that for just a moment. I absolutely appreciate your in put that’s why I started this post.. that being said please don’t try to put down someone’s intelligence when it comes to oils recommendations... I don’t drive a taxi!!! There are countless Doctors prescribing medicine that is NOT FDA approved.. Honestly I absolutely love tour input.. but because the don’t work on taxi cabs does not mean the donknow oil. Side note they also rebuild every engine the get ran at a very famous race track here in town.. so they absolutely see what happens to an engine after a years time of abuse taxi cabs wil NEVER see. That’s exactly why they recommend it. Again no hard feelings I hope but when throw stones 🤷🏼‍♂️🤷🏼‍♂️🤷🏼‍♂️
  13. So my machine shop highly recommended Brad Penn/Penngrade oil. This is the first time I’ve used it. I do not have a problem spending the extra money on good oil. I just thought this would make for a nice topic. I’m sure there are a lot of opinions on this. Stay healthy and let’s hear the stories guys!!!
  14. For what it’s worth... we have a local guy here in West Michigan, if you are into cars at all.. you may have heard of him. 🤣🤣🤣😉 If you buy a Holley Sniper kit from Steve Morris, he actually includes a couple of hours of tech support. That really tells me if/when I pull the trigger it will be Holley and it will come from Steve Morris Racing. If you don’t know him... you probably better google his name!!!!!
  15. I have built a 468 striker with and Eagle crank.. I can get the Part number if needed. It has BB Chevy h-beam rods.. also can get the part number if needed. And short stroker pistons..again if you need the part number I can provide it..now here’s my question. I took a stock 1970 Pontiac block with #15 heads that are ported and polished with big valves installed. All the above parts went to my machine shop.. a VERY high end BTW.. so VERY trustworthy. They said if I wanted to be 10.5:1 I had to deck the block, mill the heads and re-cut my intake to match... now... here is my question and I hope someone is smarter than me... I have a chance to buy an M1 procharger CHEAP. If I were to buy the 87cc edelbrocks and bolt them on stock or even a set of smogger 6x Stock would that lower my ratio enough??? I hope I’m not confusing, thanks for any help. #ponchopower
  16. This is my 70 LeMans 468 Poncho I have another set of wheels that change my car into a street beast. If you don’t like the 18’s I’ll post some pics of the 15’s soon
  17. My 1970 LeMans Sport Convertible 468 Pontiac Stroker 💪🏼
Tired of these Ads? Purchase Enhanced Membership today to remove them!
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.